Phono Testing & Vinyl Mastering

RIAA & Phono Preamplifier Measurement

With the global vinyl resurgence, demands on noise floor, headroom, and frequency response accuracy of phono stages have surged. WinAudioMLS delivers software-defined inverse RIAA generators and real-time de-emphasis filters with precision tighter than ±0.005 dB.

Standards & Time Constants

The Four RIAA Time Constants in Detail

The standardized RIAA recording curve attenuates bass frequencies to mechanically limit stylus groove excursion and boosts high frequencies to mask surface noise upon playback.

During playback, the phono preamplifier must supply the exact reciprocal response. High-grade mastering and measurement suites also account for the optional fourth pole (T4 = 3.18 µs), introduced to prevent cutter-head burn-out above 20 kHz.

3180 µs 50,05 Hz

T1: Low-Frequency Pole

Recording: transition to constant amplitude below 50 Hz. Playback: termination of the 6 dB/octave bass boost.

318 µs 500,5 Hz

T2: Midrange Zero

Recording: transition from constant velocity to constant amplitude. Playback: flat transition shelf before high-frequency roll-off.

75 µs 2122 Hz

T3: Treble Pre-Emphasis

Recording: 6 dB/octave treble pre-emphasis (+19.6 dB at 20 kHz). Playback: complementary treble de-emphasis.

3,18 µs 50,05 kHz

T4: Cutter-Head Pole (Neumann)

Prevents runaway high-frequency boost during cutting. Essential for rigorous 192 kHz lab compliance testing.

Sample Rates & Filter Accuracy

Why 44.1 kHz Fails Precision RIAA Measurement

Due to bilinear transform frequency warping near the Nyquist limit, digital IIR biquad filters deviate significantly at 44.1 kHz (>0.5 dB error at 20 kHz). True 192 kHz operation is required to achieve reference-grade measurement fidelity.

Sample Rate Error 10 Hz – 15 kHz Error at 20 kHz Ultrasonic (to 55 kHz) Lab Suitability
44.1 kHz (Standard Audio) ±0.25 dB > 0.50 dB (Warping) Unmeasurable (Nyquist) Unsuitable for lab qualification
96.0 kHz (High-Res) < ±0.01 dB < ±0.03 dB ±0.18 dB up to 40 kHz Good for routine engineering QA
192.0 kHz (#3000 + #3017) < ±0.005 dB < ±0.008 dB < ±0.02 dB up to 55 kHz Reference grade for calibration & mastering
METHODE A

Inverse-RIAA in Signal Generator

The signal generator pre-emphasizes the stimulus with the exact inverse curve. A compliant phono stage outputs a dead-flat 0.00 dB response, preventing front-end input clipping at low frequencies.

METHODE B

RIAA De-Emphasis in Analyzer

A flat multitone or log sweep is fed via an ultra-low noise attenuator (e.g. #5699) into the preamp. The analyzer applies digital RIAA de-emphasis mathematically in real time, ideal for weighted noise evaluations.

Interactive Target Calculator

RIAA & Inverse-RIAA Target Calculator

Calculate exact theoretical target dB values for any frequency under standard 3-pole RIAA and with the optional 3.18 µs Neumann ultrasonic extension.

RIAA Playback (Standard 3-Pole)
0.00 dB
Inverse RIAA (Cutting Curve)
0.00 dB
RIAA with 3.18 µs Pole (Neumann)
0.00 dB
Expected Filter Tolerance
Measurement Hardware & Software Modules

Recommended Modules for Phono & RIAA Testing

Pair our RIAA plugin with ASIO low-latency streaming and precision attenuator pads for fully automated test sequences.

Dr. Jordan DesignArt. #3017↗

Plug-in RIAA Filter

With this tool you can add the RIAA and inverse RIAA filter to both our analyzer and signal generator

Price:79,00 €net
incl. 19% VAT, excl. shipping:94,01 €
Dr. Jordan DesignArt. #3000↗

Plug-in ASIO 192kHz 24bits

Expand your measurement system to 24Bit and 192kHz Samplerate via ASIO

Price:99,00 €net
incl. 19% VAT, excl. shipping:117,81 €
Dr. Jordan DesignArt. #1999↗

software bundle for measuring electric systems

This bundle is optimized for amplifier testing or general electrical testing We recommend it for the following group of devices: Pre-amplifiers, Radio transmissions Power-amplifiers, Soundcards AD/DA converter, Tube-amplifiers, Sound control devices, Filter

Price:399,00 €net
incl. 19% VAT, excl. shipping:474,81 €
Dr. Jordan DesignArt. #1722↗

LAB

Log-Sweep (chirp), 192kHz sample rate, incl. USB Dongle

Price:479,00 €net
incl. 19% VAT, excl. shipping:570,01 €
Dr. Jordan DesignArt. #5699↗

XLR attanuator

XLR attanuator

Price:25,00 €net
incl. 19% VAT, excl. shipping:29,75 €
Dr. Jordan DesignArt. #9012↗

Measurements in our lab with Audio Precision APX555

We offer measurement services with our APX555 in our LAB for your devices

Price:199,00 €net
incl. 19% VAT, excl. shipping:236,81 €
More WinAudioMLS DSP Simulators
Software Platform
WinAudioMLS Editions, Plug-ins & Bundles
→
Procurement & License
Request WinAudioMLS & RIAA Plug-in Quote
→