Asynchronous Measurement · Continuous Real-Time SRC & Fractional-Sample Interpolation

Asynchronous Audio Testing: Clock Drift in USB Microphones, Bluetooth & Sub-Sample Phase Alignment

In the past, output (DAC) and input (ADC) lived on the same PCI soundcard sharing a single crystal clock. Today, engineers routinely measure across separate clock domains: a USB measurement microphone (such as our ATD4-S, ATD5-T, MTG MV240, or MiniDSP UMIK-1/2) runs on its own internal crystal, while the excitation signal plays through a laptop DAC, Bluetooth sink, Dante/AVB network, or automotive head unit. Without clock compensation, transmitter and receiver drift apart—corrupting impulse response, phase, and high-frequency magnitude.

What Many Engineers Miss in REW or Standard Analyzers:

Why Two Separate 48,000 Hz Devices Never Run at the Exact Same Speed

Every crystal oscillator inside a USB microphone, smartphone, or DAC has a manufacturing tolerance of typically ±20 ppm to ±100 ppm (parts per million) plus thermal drift. When your laptop DAC transmits at 48,000.000 Hz, a USB microphone with a -30 ppm offset actually samples at 47,998.560 Hz (drifting by 1.44 samples every second).

We built a continuously tunable real-time arbitrary Sample Rate Converter (millihertz resolution) and fractional-sample delay interpolation directly into WinAudioMLS. Combined with our Log-Chirp correlation engine (WinAudioMLS LAB & Akulap), this solves the exact four modern measurement challenges where standard tools fail:

Section 1 · 4 Modern Use Cases for Real-Time SRC & Fractional-Sample Delay

Where Asynchronous Clocks and Sub-Sample Delays Occur Every Day

Use Case 1 · USB-Messmikrofone (ATD4-S / MV240 / UMIK)

USB Measurement Mic Input + Separate Amplifier/DAC Output

A USB microphone cannot be wordclock-locked to a separate loudspeaker DAC. In correlation measurements (especially MLS or long averages), even a 20–50 ppm crystal offset smears the impulse response, rotates phase, and causes up to 5 dB of false high-frequency roll-off above 10 kHz.

Solution A (Real-Time SRC): Using the Pitch control in WinAudioMLS, you continuously tune the effective sample rate to match your USB microphone's exact crystal (e.g., 47,998.56 Hz) until the impulse peak maximizes. Solution B (Chirp): Our Log-Chirp (WinAudioMLS LAB & Akulap) is inherently immune to 20–50 ppm clock drift.

Use Case 2 · Sub-Sample Phase (7,1 mm = 150° Fehler)

Loudspeaker Crossover Design & Millimeter-Precise Time Alignment

At 48 kHz, a single sample interval is 20.83 µs—during which sound travels 7.14 mm in air. At 20 kHz, 1 sample equals 150° of phase rotation! If an analyzer can only shift time windows by integer samples, a steep residual phase ramp always remains, hiding the true crossover phase response.

By enabling Sample Rate Conversion in the synchronization menu, WinAudioMLS shifts the impulse response by fractions of a sample (fractional-sample delay, e.g., 0.05 samples = 1 µs = 0.34 mm). This compensates acoustic flight time to a tenth of a millimeter, revealing the pure filter phase.

Use Case 3 · Automotive, Bluetooth, TWS & Smart Speakers

Closed-Loop Devices Without Line-In (Car Audio, Bluetooth, TWS, Smart Speakers)

Modern Bluetooth speakers, True Wireless (TWS) earbuds, hearing aids, and automotive infotainment systems often lack analog line inputs. Test signals must be streamed or played from local storage while the measurement microphone records on the PC—100% asynchronous with variable latency.

Our signal generator exports precision test sequences as WAV files. During capture, WinAudioMLS's real-time SRC compensates the Bluetooth or head-unit DAC clock offset, or you can use the 185 ms Log-Chirp in the LAB edition for instant frequency response and distortion curves.

Use Case 4 · Große Hallen & Thermische Drift (Doppler)

Large-Venue PA Tuning & Room Acoustics Under Airflow / Thermal Gradients

In large auditoriums, stadiums, or industrial halls, the speed of sound shifts due to temperature gradients (~0.6 m/s per °C, equivalent to ~1,750 ppm per °C!) and HVAC airflow. Physically, this acts exactly like a continuous sample rate drift between loudspeaker and microphone.

While classical MLS correlation breaks down at high frequencies in large time-varying rooms (Manual Chap. 17.1), our Log-Chirp methods (WinAudioMLS LAB & Akulap) and SRC tracking remain stable.

Section 2 · Interactive Simulator 1: USB Microphone Clock Drift & Real-Time SRC (Pitch Tuning)

Test How Crystal Clock Drift (ppm) Corrupts Measurements – and Compensate It Live via SRC

Set a typical crystal clock offset for your USB microphone or Bluetooth receiver on the left (e.g., -35 ppm). Watch the uncorrected MLS curve collapse above 8 kHz in the chart. Then drag the WinAudioMLS Real-Time SRC Pitch slider (or click 'Auto-Sync SRC') until the analyzer sampling rate locks onto the true hardware clock:

-35 ppm
0 ppm
True Hardware Clock Frequency
47998.320 Hz
Tuned WinAudioMLS SRC Frequency
48000.000 Hz
Residual Clock Error (Net Drift)
-35.0 ppm
Section 3 · Interactive Simulator 2: Fractional-Sample Delay Interpolation for Phase Responses

Why Integer Sample Shifts Are Not Enough for Loudspeaker Phase Measurements

We measure a 2-way loudspeaker crossover at 2,000 Hz (true phase shift 180°). Due to a tiny residual microphone distance offset of just +2.8 mm (+0.40 samples at 48 kHz, or 8.3 µs flight time), a steep linear phase slope is added—producing an extra -60° to -144° phase error at 20 kHz and causing phase wrapping. Use the Fractional-Sample slider (0.01-sample resolution) to strip out the exact flight time:

+1.40 Samples
-1 Sample
-0.00 Samples
Residual Flight-Time Error (Δt)
+8.3 µs
Equivalent Air Path Error (at 343 m/s)
+2.86 mm
Phase Error at 10 kHz
-30.0°
Phase Error at 20 kHz
-60.0°
Matching USB Measurement Microphones, Calibration-Proof Interfaces & Software

Measurement Systems for USB Microphones, Asynchronous DUTs & Phase Analysis

Combine our calibrated USB measurement microphones (ATD4-S, ATD5-T, Microtech Gefell MV240, or MiniDSP UMIK-2) directly with WinAudioMLS PRO EX / LAB or Akulap:

Dr. Jordan DesignArt. #1722↗

LAB

Log-Sweep (chirp), 192kHz sample rate, incl. USB Dongle

Price:479,00 €net
incl. 19% VAT, excl. shipping:570,01 €
Dr. Jordan DesignArt. #1721↗

Pro EX

extends to 2 channel, THD, Impedance, Spectrogram

Price:279,00 €net
incl. 19% VAT, excl. shipping:332,01 €
Dr. Jordan DesignArt. #6510↗

NEW: module based USB measurement Microphone 1/2" ATD5-T

module based USB measurement Microphone 1/2" ATD5-T

Price:825,00 €net
incl. 19% VAT, excl. shipping:981,75 €
Dr. Jordan DesignArt. #6533↗

USB measurement Microphone for Akulap

USB measurement Microphone optimized for Akulap

Price:750,00 €net
incl. 19% VAT, excl. shipping:892,50 €
Dr. Jordan DesignArt. #75240↗

MTG Microtech Gefell MV240 USB Interface 1/2"

MTG Microtech Gefell MV240 USB Interface 1/2"

Price:1963,03 €net
incl. 19% VAT, excl. shipping:2336,00 €
Dr. Jordan DesignArt. #6532↗

USB measurement Microphone MiniDSP UMIK 2 192kHz

USB measurement Microphone MiniDSP UMIK 2.

Price:326,89 €net
incl. 19% VAT, excl. shipping:389,00 €
More WinAudioMLS DSP Simulators
Hardware Practice
Calibrated USB Measurement Microphones & Async Clocks
→
Correlation Simulator
Log-Sweep / Chirp Method vs. MLS
→
Procurement & License
Request WinAudioMLS & Microphones Quote
→